Sunday, September 27, 2009

EASA Essay Paper Module 10, Module 9 & Module 7

EASA Essay Paper
Module 10

1.You are a JAR OPS organization. Explain how you would set-up an aircraft maintenance organization.

2. Describe in detail the process of obtaining a Part-66 Basic License and then describe how a Part-145 quality department can issue a type approval

3. Describe the process for attaining a Part-66 license and how you can obtain an extension to the basic license.

4. What are the relationships between the ANO, BCARs, JARs and AWNs. List the AWNs that are applicable to the Licensed aircraft engineer.

5. An aircraft has suffered structural damage due an accident/incident. Describe the inspection and management procedures and relevant paperwork for rectification.

6. You are a Part-145 company - what audits would the quality department need to carry out to retain the company approval? An organogram would help your answer.

7. Explain in some detail what areas of a 145 approved company need to be audited by the company's quality department. An organogram of the 145 structure may be helpful

8. Describe the JAR 66 License categories with experience requirements.

9. What are the maintenance requirements of a company under JAR OPS 1:890?

10. How would you convert BCAR to JAR license?

11. What are the relationships between the ANO, BCARs, JARs and AWNs. List the AWNs that are applicable to the Licensed Aircraft Engineer.

12. What are the considerations when moving a private category aircraft into the Commercial Air Transport category?

13. What organization system is required under JAR OPS Subpart M to support the continued airworthiness of its aircraft?

14. As an aircraft operator, how do you maintain your aircraft and what checks do you do?

15. Describe the process for attaining a JAR 66 license and detail the engineers’ responsibilities under JAR 145.

16. What are the considerations and certifications for release to service when a licensed engineer carries out a component replacement?



Module 9

1. Describe in detail the effects of stress on an engineer and how environmental factors affect stress. Discuss how these affects can be minimized.

2. If a major skin repair was being carried out on an aircraft and you were the team leader, and the repair was not going to be completed within your shift period, how would you do a shift handover for the next shift?

3. Describe human error in aircraft maintenance and the inspection
environment, and describe how it can be minimized.

4. There are many different types of maintenance error reporting schemes. Maintenance Error Decision Aid (MEDA) is one. Explain its implementation and how this is achieved within a company?

5. Name two pressures the engineer is subjected to, how they originate and how to prevent them

6. With regard to circadian rhythms, expand on the following:
• What does 'circadian' mean?
• What is a 'circadian rhythm'?
• How is the body affected after a long flight over several time zones?
• Ref. above - how can the effects be minimized?
• What is meant by 'post lunch low'?
• With respect to circadian rhythms, what is meant by 'acrophase'?

7. You are a shift leader carrying out a major airframe repair that will not be completed during your shift. How are you going to communicate this to the incoming shift with regards to outstanding work, data and spares?

8. What are the different types of stress encountered at the workplace, and as an employer, what are the ways to relieve stress of your employees?

7. What is the impact of human factors on:
a) Maintenance scheduling, and
b) Environmental factors

8. What are the human factors effecting the maintenance?

9. Describe ‘Maintenance Error Decision Aid’ (MEDA) and how is it utilized for accident prevention.








Module 7

1. What is an oversize rivet and when would it be used?

2. Discuss the methods of protection against HIRF and the checks / inspections which would be carried out after a fault was entered in the tech log.

3. You are required to carry out a torque loading. Describe the procedure including all checks and tests to be carried out.

4. You are required to carry out a bonding test on an aircraft. Describe the procedure including all checks and tests to be carried out.

5. Describe the procedure to refuel a medium sized passenger jet Include all safety checks that should be observed.

6. You are tasked with securing a small 50-seater aircraft due to high winds. How and where would you picket the aircraft and what checks would you carry out?

7. Describe the procedure for placing a medium sized aircraft into storage for 6 months. Include any maintenance checks that would be required.

8. List the precautions before, during and after painting an aircraft.

9. Discuss the precautions you would take, before during and after a windscreen replacement.

10. A fiber-reinforced flap has been found damaged (soft spot). What inspections and repairs would you carryout?

11. What are the benefits of cadmium plating?

12. What is 'Stressed Skin' construction? What inspections would you carryout to it during servicing?

13. After a heavy landing, describe what checks you would carry out including what questions you would ask the flight crew.

14. Describe the procedure for weighing an aircraft. Include all precautions to be taken before during and after the weighing.

15. Describe the procedure for carrying out a dye-penetrant NDT check on an aircraft component.

16. On carrying out a system check of a stall warning system it is discovered that the first officer's stick shaker is inoperative. Describe how you would fault find the system and how you would rectify the defect.

17. On trouble shooting an IDG overheat lamp fault, it was discovered that the connector of the IDG had evidence of overheating. Describe in detail the fault rectification process and how all the work should be recorded.

18. Describe the procedure for towing an aircraft from the hangar to the line, including all safety aspects.

19. Describe the procedure you would follow to remove corrosion from a component.

20. Describe what you would do if the aircraft had suffered a lightning strike.
21. Describe the different methods of de-icing an aircraft. Include details of types of fluid used.

22. During an engine start it is noticed that the No.2 ignition system is not working. What are you going to do to fix the problem and what certification (if any) is required?

23. How is safety in the aircraft hangar achieved?

24. Describe the procedure used for trouble shooting a DRIVE light of an IDG?

25. On a walk round inspection you notice smoke/vapour in the starboard wheel well. Describe the actions you would take and list possible causes.

26. The pilot reports a burning smell from the flight deck air conditioning system. State your actions and detail possible causes.

27. Describe how you would replace a PCB and the precautions you would take.

28. Discuss the methods of protection against HIRF and the checks/inspections that would be carried out after a fault was entered in the tech log.

29. On carrying out a system check of a stall warning system it is discovered that the first officer’s stick shaker is inoperative. Describe how you would fault find the system and how you would rectify the defect.

30. On trouble shooting an IDG overheat lamp fault, it was discovered that the connector of the IDG had evidence of overheating. Describe in detail the fault rectification process and how all the work should be recorded.

31. During an engine start it is noticed that the No.2 ignition system is not working. What are you going to do to fix the problem and what certification (if any) is required?

32. After heavy maintenance an aircraft is taken outside for engine runs. the engine will rotate but not ignite, describe the possible causes of this and how you would go about fault finding this problem

33. On a walk round inspection you notice smoke/vapour in the starboard wheel well. Describe the actions you would take and list possible causes

34. The pilot reports a burning smell from the flight deck air conditioning system. State your actions and detail possible causes.

35. Describe how you would replace a PCB, and the precautions you would take.

36. Describe in detail your actions after finding a landing gear strut low.

37. On a major hangar inspection you find corrosion in an unpressurised panel. Detail your actions to return the aircraft to service.

38. Describe the procedures when inspecting a brake unit. What would you do on discovering a brake unit 'worn to limits'?

39. Describe the procedure, documentation used, and those to be filled out when jacking a nose wheel aircraft over 5700kg.

40. List NDT techniques commonly used for inspecting aircraft structure and
components. Give details of defects it will find, what materials the techniques may be used on and what are the chief advantages and disadvantages of each technique

41. There is 2 inches of wet snow on the aircraft, the temperature is –2oC, what are your considerations before releasing the aircraft for departure?

42. Describe how you would carry-out a fuel contamination test.

43. Describe how tooling is controlled within a Part-145 maintenance organization.

44. Describe the procedure of a hold-over item

29 comments:

  1. thanks alot atleast i have to do revision

    ReplyDelete
  2. can i get the example essay answers for the question number 2 & 14

    ReplyDelete
  3. please help me and how i must study ? please

    ReplyDelete
  4. how is the marking scheme for the essay question?

    ReplyDelete
  5. Replies
    1. You got answer of essay 7-9-10 ?
      rasulm2015@yahoo.com
      Thank you(:

      Delete
  6. Anyone have essay 7-9-10 answer please I got exam next week!
    rasulm2015@yahoo.com

    ReplyDelete
    Replies
    1. did u get the answer for essay module 9? can u email to me asap at ibnuyusof18@gmail.com

      Delete
  7. Can i get answer please for Q2 in module 9

    ReplyDelete
  8. got the answer module 10 question 16? please emain me chscheah@yahoo.com

    ReplyDelete
    Replies
    1. Try search it on google. Ive found a lot of answers

      Delete
  9. This would be great..i can make the answers before i start my semester..thank you very much!

    ReplyDelete
  10. hello, anyone with recent mod 7,9 $ 10 essay questions and possible anwers? pliz assist. my email is fransnjoro@yahoo.com

    ReplyDelete
  11. Question in todays Module 9 essay;

    Due to a design flaw in an aircraft, the a/c suffers structural failure some years later. Describe failures leading to the incident and which error model would best describe it.

    ReplyDelete
    Replies
    1. Please do you have answers to this particular question.

      Delete
  12. Please do you have answers to this particular question

    ReplyDelete
  13. Hellow any one can help me in essay answers i am stuck.
    Please email me easa essay 7 9 and 10 answers.
    junaid.younus.avionics@gmail.com

    ReplyDelete
  14. please assay answers for mod 7,9&10

    ReplyDelete
  15. Hi! can i get the module 9 question 2 answer? just for that question. tq so much if you help me :)

    ReplyDelete
  16. Can someone email me the answers to the essay questions please.12jahknox@gmail.com (7,9 and 10)

    ReplyDelete
  17. I ask questions and essay answers in module 9 too. please u can sent paper at email lindaryn@outlook.com thx.

    ReplyDelete
  18. Can anyone send me the answers for these questions to my email.
    ayoayojjayathennakoon@gmail.com

    ReplyDelete
  19. can i have the ans wer for all those question mod 7,9,10? muhdhakim93@gmail.com

    ReplyDelete
  20. Can anyone send me the answers for module 9? gavril_alexandrucm20@yahoo.com
    Thanks a lot!

    ReplyDelete
  21. Please Someone send me ans on r.ksingh029@gmail.com.

    ReplyDelete
  22. Hello sir!
    After reading the essay and question module blog posted by you, all of us have received a lot of information. Heartfelt thanks for sharing this information among us. I Malls And Brands online mobile store UAE

    ReplyDelete
  23. This information paper provides a lot of information for all of us. While we have gained much information from the questions and answers given in these model papers, I Culex USA Air duct cleaning fort Lauderdale

    ReplyDelete